ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.
|Genre:||Health and Food|
|Published (Last):||10 October 2018|
|PDF File Size:||20.12 Mb|
|ePub File Size:||7.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
A787 Type 1, 2, 3, 4 & 6
Within the text, the SI units are shown in axtm. The values stated in either SI units or inch-pound units are to be regarded separately as standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The steels shall conform to elemental tolerances for product analysis.
A Mechanical Tubing | Alro Steel
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Historical Version s – view previous versions of standard. Outside Diameter Tange, in.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Within the text, the SI units are shown in brackets.
ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel
Link to Active This link will always route to the current Active version of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while in coil form.
A Type 6 Tubing provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes. This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order asttm the applicable M specification designation SI unitsthe inch-pound units shall apply.
This abstract is a brief summary of the referenced standard. Carbon Steel A Tube Exporter.
This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet.
Combining values from the two systems may result in non-conformance with the standard. Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided.
Sizes outside the ranges listed above may be ordered provided all satm requirements of the specification are met. Low-carbon steels and other carbon steels shall conform to the required chemical composition for carbon, manganese, phosphorus, and sulfur. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated to convert the coating into a zinc-iron alloy.
ASTM A Type 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded.
ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A Combining values from atsm two systems may result in non-conformance with the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.